These digital voltmeter (type DMV) are accurate and are characterized by steady bright 7-segment LED display and are available in compact size of 96 X 96 X 60mm. Normally available for range of 0-600V AC, the These digital voltmeters (type DMV) are also available for ranges from 0-200mV, 0-2V, 0-200V, direct reading DC or AC. They are also available for PT operated HT applications. Ripple integration provided in DC meters gives stable display for bridge rectified power supplies.

These digital ammeter are accurate, and are available in compact size of 96 X 96 X 60mm. Normally available for CT operated AC application, the digital ammeter is also available for ranges of 0-2mA, 0-20mA, 0-2A and 0-5A, direct reading DC or AC. CT operated digital ammeter are available in two versions. Factory set CT ratio: The CT ratio specified by the user is programmed into the meter, the meter then shows the CT primary current based on the secondary current received by it. Scalable CT ratio: The User can select the CT ratio by means of a DIP switch located at the rear of the meter. The meter is programmed for a CT secondary rating of 5Amps. The CT primary rating is selectable from 100 Amps to 1600 Amps in steps of 100 Amps. This version enables reduction of inventory and also avoids re-calibration in case of changes at Scalable CT ratio.

These digital frequency meter (type DMF) are accurate and are available in compact size of 96 X 96 X 60mm. These digital frequency meter (type DMF) are designed to accept wide-ranging voltage input from 50V to 600V. Available for the Mains Frequency range of 45.0-55.0Hz, the display of the meter is exceptionally steady compared to some other makes of frequency meters that are based on counting circuits. The Syntron Frequency Meter is based on a built in frequency to voltage transducer. The output of the transducer being integrated for conversion to digital display, the display is steady, and accurate.

These digital Watts, KW and MW meters (types DM1P1EW, DM3P2EW and DM3P3EW) are accurate and are available in compact size of 96 X 96 X 110mm. The digital Watts, KW and MW meter (types DM1P1EW, DM3P2EW and DM3P3EW) is Micro controller based and Time shared four-quadrant multiplier technology is used for accurate measurement at all power factors. The Micro controller multiplier provides very accurate measurements. The meters are available in single-phase single element (type DM1P1EW), three phase double element (type DM3P2EW) and three phase triple element (type DM3P3EW) versions, for LT as well as HT applications.

These digital var, Kvar and Mvar meters (type DM3P2EVAR) are accurate and are available in compact size of 96 X 96 X 110mm.The digital var, Kvar and Mvar meter (type DM3P2EVAR) is Micro controller based. Time shared four-quadrant multiplier technology is used for accurate measurement at all power factors leading as well as lagging. The Micro controller multiplier provides very accurate measurements. Full-scale display of up to 9999 is possible because of the Micro controller, enabling direct display of the input variable. The meters are available in three-phase double element version for LT as well as HT application

(cos PI) (types DM1P1EPF, DM3P1EPF, DM3P2EPF and DM3P3EPF) These digital power factor meters are accurate and are available in compact size of 96 X 96 X 60mm for single element PF meters and 96 X 96 X 110mm for three phase meters. The meter is Microcontroller based. These digital power factor meters are three-and-a-half digit meters, showing accurately power factors from 0.000 to 1.000. Separate lag/lead indications are provided by LEDs. The absence of current is shown by the micro controller as 1.uuu and wrong external connections are shown as 2.uuu as per standard practice of Syntron.

(types 0-5V DC and 4-20mA DC) These digital  meters for process signals are accurate and are characterized by steady bright 7-segment 12.7mm LED display and digital  meters for process signals are available in compact size of 96 X 96 X 60mm.The meter is designed to display the parameter being measured by a transducer.

Our range of combination meter V-A-F (DM 3060) is available with accurate measurement meters. Some of the features of our combination meter V-A-F (DM 3060) includes:

• True RMS 4 Digit measurement of Voltage and Current
• Four Digit Frequency measurement
• Conveniently accessed DIP switch at rear four CT selection
• Flicker free bright 14.2 mm LED display
• Auto scroll facility
• 96 mm x 96 mm DIN x 85 mm Depth
• Flush mounting case
• Built in Syntron reliability

Applications : Gensets – True RMS measurement gives correct values in presence of harmonics AMF panels-Compact instrument for multi –parameters and true RMS measurement for the Genset Power control panels (PCCs) – Compact instrument for multi-parameters Power Factor Control panels – Compact multi parameter measurement Test laboratories-for quick checking of instruments

Features: Measurement: Voltage: 0-300V Line to Neutral of all Three phases to phase of all Three Phases Burden: 0.2 VA approx Current: 0.5 Amps in all three phases scaled according to the CT rating selected on DIP switch at rear. Burden: 0.2 VA approx Permissible overload : 20% Frequency: 45.00 to 65.00 Hz Accuracy: +/- 0.5% +/- 1 digit of full scale for voltage and current. +/- 0.05 Digits for Frequency meter Aux supply: 180V to 260V Burden: 3VA approx The above measurement specifications are for the following environmental conditions: Operating temperature: -10 to 55 deg C Storage Temperature:-20 to 70 deg C Humidity: Less than 95% RH non –condensing Operation : Switch on : Amps of R phase, Voltage R-N Press switch : Amps of Y phase , Voltage Y-N Press switch : Amps of B phase,Voltage B-N Press switch :Amps of R phase, Voltage R-Y Press switch :Amps of Y Phase, Voltage Y-B Press switch : Amps of B Phase, Voltage B-R Pressing switch once more revert measurement back to the state as switch on . Instrument goes in AUTO SCROLL MODE if the switch is kept pressed for 5 second or more and released.

Our range of combination meter KVA-KW-PF (DM 3150) is available with Power Factor measurement. Some of the features of our combination meter KVA-KW-PF (DM 3150) includes:

• True RMS 4 Digit measurement of KVA, KW and power Factor for sine wave as well as distorted waveforms
• Four digit Power Factor measurement
• Conveniently accessed DIP switch at rear for CT selection
• Flicker free bright 14.2 mm LED display
• Auto scroll facility
• 96 mm x 96 mm DIN x 85 mm Depth, flush mounting case
• Built in Syntron Reliability

Applications: Gensets – True RMS measurement gives correct values in presence of harmonics AMF panels –Compact instrument for multi – parameters and true RMS measurement for the genset Power control panels (PCCS) – compact instrument for multi-parameters Power Distribution Boards (PDBS ) – mots sutable for feeders for DC drives and VFDS Power factor Control panels – Compact multi parameter measurement Maximum Demand Controllers – Compact multiparameter measurement for demand . Test laboratories – for quick checking of instruments Features: Measurment: Voltage : 0 300 V line to neutral of all three phases. Burden : 0 2 VA approx Current : 0 5 Amps in all three phases scaled according to the CT rating selected on DIP swith at rear Burden : 0 2 VA approx Permissible overload: 20% Frequency: 45.00 to 65.00 Hz Measured values: KVA: for all popular CT ratios from 30/5 to 1500/5 by true multiplication of true RMS voltage and Current measurement. KW: for all popular CT ratios from 30/5 to 1500/5 by true four quadrant multiplication of voltage and Current measurement. Power Factor : Unit measures Power Factor by ratio of KW and KVA, and not merely cos phi. This gives true measurement in presence of harmonics. Accuracy : +/- 0.5%+/- 1 digit of full scale for voltage and current . +/- 0.05 Digits for Frequency meter Aux supply : 180V to 260V Burden : 3VA approx The above measurement specifications are for the following environmental conditions : Operating temperature: -10 to 55deg C Storage temperature: - 20 to 70deg C Humidity: less than 95% RH non-condensing Operation: Switch on : KVA ,KW and power Factor of R phase . Press switch:KVA, KW and power Factor of Y phase. Press switch: KVA, KW and power Factor of B phase. Press switch: KVA , KW and power Factor of sum of R,Y,B phases. Pressing switch once more reverts measurement back to the state as at switch on. Instrument goes in scroll mode if the switch is kept pressed for 5 second or more and released.

Our range of power analyzer meter (DM3240.) Our power analyzer meter (DM3240) are available with the following features:

• State of Art Micro controller technologies
• Multi-parameter Measurement of AC Three Phase Four Wire System
• True RMS Measurements
• Four Quadrant Measurements for KW, Kvar and KVA
• Switch Selectable CT ratio
• 4 Digit 14.2mm Bright Red LED Display of Selected Parameter.
• Parameters measured: Power Factor (PF), Harmonics (THD) Voltage (V), Current (I), Kilowatts (KW), Active Power (Kvar), Maximum Demand (KVA), Frequency (Hz)
• Build in Syntron Reliability